We’re in love with this colourful gaming PC, which options not one however two water-cooled PCs, each of which function Nvidia GeForce RTX 3000-series GPUs and top-end Intel CPUs. PC modder Kris Butterill modded a Raijintek Enyo case to create this monster dual-system construct for Intel’s Gamer Days marketing campaign, and it options hand-bent tubing, {custom} 3D-printed components, and 4 reservoirs.
Because of our quickly rising PC constructing Fb web page, we’ve seen many {custom} gaming PCs, from mods primarily based on current case designs to scratch PC builds. You may even submit yours for consideration proper right here. Now let’s discuss to Kris about how he created this beautiful twin system.
: How did this Intel dual-PC venture begin?
Kris: Intel had seen a construct I did for MSI, a venture for a YouTuber referred to as Mumbo Jumbo, and actually beloved the ultimate aesthetic. It contacted me to ask if I might put one thing collectively as a prize for its 2021 Intel Gamer Days marketing campaign. The transient was to create one thing actually excessive, a twin system with one facet devoted to PC gaming and one facet devoted to streaming.
This meant the winner would get a rig that would deal with just about something they might throw at it, plus it needed to look fairly! The main target was celebrating the Intel Gamer Days marketing campaign, so it needed to stand out and be themed round Intel’s branding, therefore the yellow and blue coloration scheme. It wanted to look as clear and distinctive as doable, whereas retaining the core Intel branding parts to make it immediately recognizable.
Are the 2 chassis mainly similar however with the yellow and blue swapped round?
They’re near similar, though either side of the chassis has some delicate modifications to parts, such because the fan colours and structure of the water-cooling loop. I wished to create a system that wrapped round itself, so you can see that it’s one thing particular and consider all the important thing particulars from any viewing angle.
Are the 2 techniques fastened collectively?
It’s designed to be one full construct with each side completely connected to one another. The one draw back is the burden of it once you wish to transfer it round. It separates into its two sides for simpler upkeep and positioning, although, and either side is completely impartial.
My unique plan was to run the coolant from the pumps on one facet to chill the parts on the opposite system. Nonetheless, that meant actually overcomplicating the construct, and would lead to such a mash-up of coloration on either side that it wouldn’t look proper. It additionally wanted to be hand-delivered to Intel UK, and to some extent, it wanted to be fairly sensible to ship out to the winner.
It’s troublesome to inform, however is that this a scratch construct or did you utilize an current case?
Thanks for the kudos, however no, that is primarily based on an off-the-shelf chassis, consider it or not! The entire venture wanted to be primarily based round a chassis that would provide mounting for twin ATX-sized techniques, and to be trustworthy, there aren’t any off-the-shelf single instances that do this out of the field.
Nonetheless, the Raijintek Enyo is a modular chassis that had potential to make use of two of them collectively. I needed to modify the mounting system and primarily bolt them again to again, utilizing simply the front-facing sides of every chassis equipment.
When in dialogue, neither Intel nor myself could possibly be one hundred pc positive that the idea and thought would work till the instances have been ordered and landed with me. As soon as they have been with me, although, it quickly grew to become clear that our intention was achievable, albeit with some tinkering right here and there.
The modular design of the Enyo made it pretty simple to place all of it collectively. I needed to drill and modify some small facets of the instances with a view to get the motherboard mounting appropriate. There was additionally some customization concerned when shifting the mounting areas of the facility provides and prime radiator panels.
In its ultimate configuration, the case is solely enormous! As soon as the modular panels had been modified, it was then time to construct it up for check becoming and ensuring that every one the components related completely. The Enyo does have some sway in it although – if Raijintek ever makes a V2 version of this open-air case then it will be good to have slightly extra rigidity with thicker panels. Total, although, it’s sturdy sufficient as soon as it’s all constructed up.
These are some strikingly daring and vivid colours. What paints did you utilize?
Each modder had a weak spot, whether or not they prefer to admit it or not, and paint is a type of areas for me. Given the sheer dimension of this venture, and the necessity for the very best longevity, I made a decision to outsource the paint job. It’s powder-coated for added sturdiness and the colours have been RAL-matched to Intel’s branding. Initially, the thought was to maintain the colours fully separate, however after getting the components again, swapping over the facility provide shrouds actually added some additional distinction to the theme.
How did you create the diffuse lighting impact? Is that translucent acrylic?
Certainly, I designed up the panels in CAD to match up with the mounting holes for the fan placement within the backside shrouds. They have been then laser-cut, with RGB strips added to the sides to permit the sunshine to diffuse by them. All of the RGB lighting is managed by a fairly in-depth Corsair iCUE-based system working two Corsair Commander Professional items per facet.
Take us by the water-cooling techniques.
There are two 480mm Alphacool radiators per system. Alphacool is my go-to cooling accomplice, because it offers me peace of thoughts on the subject of reliability and high quality. I didn’t go for 45mm-thick rads, because the Enyo case’s weight-bearing capability isn’t good, so I used 30mm-thick radiators.
I designed and 3D-printed some {custom} mounts for the reservoirs, because the Enyo’s commonplace mounting sample didn’t match as much as the Alphacool mounting brackets. Regardless of the 2 reservoirs in every system, the loops aren’t cut up both – every system has one massive elaborate run, fairly than two separate loops.
I might have made two separate water-cooling loops for the CPU and GPU in every system, however this setup helps to bulk out the system, provides a singular function and builds in some redundancy ought to a pump fail sooner or later.
I hardly ever pre-plan tubing runs, as what you take note of may not really be bodily doable. All of the tubes have been bent by me, and a few of them required 4 or 5 makes an attempt to make sure they have been completely good. I used Alphacool 13/10mm PMMA tubing – I favor it to PETG – and used the built-in tubing pass-through on the chassis.
The place are all of the cables hidden?
The cables are predominantly hidden behind the facility provide shrouds. There’s all of the Corsair iCUE wiring that goes to the followers and lighting, with custom-length cables from the SFX 1000W PSUs to the motherboards and GPUs.
There’s a small hole between either side of the system that’s used for a number of the cable runs. Planning this included measuring up for the {custom} cables – I didn’t need any extra as a result of that might simply give me one other tidying downside down the road.
There’s a whole lot of room below the underside shrouds, and I designed and 3D-printed some {custom} brackets for the Commander Professional items to sit down inside them. I like utilizing my 3D printer – it’s such a terrific device to make use of once I wish to overcome little issues, akin to these. I didn’t wish to use 3M pads, as they may fail six months down the road.
What specs did you select and why?
I like Asus {hardware}, so it wasn’t arduous for me to determine what I wished to make use of for the core of every system. Intel wished to go excessive, primarily handing me (with sure phrases) a vast funds for {hardware}. For gaming, I believe what we used was excessive.
The Asus Glacial is solely a stunning motherboard, with its built-in water-cooling assist and intensive options, whereas Asus’ Hero vary is considered one of my all-time favorites. It’s all primarily based on Intel Eleventh-gen {hardware}, so there’s a Core i9-11900K and Core i7-11700K, plus Asus TUF Nvidia GeForce RTX 3090 and RTX 3080 graphics playing cards, 10TB of PCIe 4 storage from WD and Corsair Dominator RAM. All in, I believe there’s over $15,000 price of drugs sat right here, simply in {hardware}, so it’s not like we skimped anyplace!
Did you come throughout any difficulties?
A great deal of them! The largest, although, was accommodating the sheer dimension and weight of this factor in its entirety. It’s slightly simpler to deal with when it’s separated into single entities, however it requires two folks to raise it when it’s all bolted collectively, and I wouldn’t suggest making an attempt to maneuver it as a complete unit. Whoever finally ends up with this machine wants to decide on the place it’s going to dwell correctly, as a result of it isn’t going anyplace as soon as it’s in place!
The highest of the Enyo case additionally sags slightly with the burden of the 30mm-thick rads. I might have added helps, however that might have taken away a number of the total look of the construct, plus it’s actually not a significant factor because it stands.
How lengthy did it take you to finish this construct?
I’d say round eight-10 weeks, however a whole lot of that point was all the way down to the paint job and ready for arts. The wait looks like ceaselessly on a venture akin to this one once you simply wish to crack on with it.
Is there anything you wish to add in regards to the construct course of?
In all probability a very powerful factor about this entire venture is that Intel was giving it away! Coming into to win this technique actually helped a non-profit group, Technovation, which empowers women to grow to be leaders by tech training. The Technovation Ladies program equips younger ladies (aged eight-18), with the assist of volunteer mentors and oldsters, working in groups to code cell apps that tackle real-world issues.
Are you fully proud of the top outcome, or do you want you’d finished a few of it in another way looking back?
No modder is each actually proud of a construct! There’s all the time one thing you’ll change, strive in another way and so forth. Total, although, I don’t suppose it turned out too dangerous, eh?
Pictures by Andre Pattenden.
Twin Intel gaming PC specs:
Entrance PC
- CPU: Intel Core i9-11900K
- Motherboard: Asus ROG Maximus XIII Excessive Glacial
- Case: Raijintek Enyo
- Storage: 3 x 2TB WD Black PCIe 4
- Graphics card: Asus TUF GeForce RTX 3090
- Reminiscence: 64GB Corsair Dominator
- Cooling: Full {custom} water-cooling loop, with 2 x Alphacool Eisbecher Aurora reservoirs, 2 x Alphacool VPP655 pumps, 2 x Alphacool ST30 480mm radiators, 1 x Alphacool GPU waterblock. 8 x Corsair LL120 followers
Rear PC
- CPU: Intel Core i7-11700K
- Motherboard: Asus ROG Maximus XIII Hero
- Case: Raijintek Enyo
- Storage: 2 x 2TB WD Black PCIe 4
- Graphics card: Asus TUF GeForce RTX 3080
- Reminiscence: 64GB Corsair Dominator
- Cooling: Full {custom} water-cooling loop, with 2 x Alphacool Eisbecher Aurora reservoirs, 2 x Alphacool VPP655 pumps, 2 x Alphacool ST30 480mm radiators, 1 x Alphacool GPU waterblock. 8 x Corsair LL120 followers
That is excellent work Kris – the laser-cut acrylic panels look nice with the sunshine shining by them, and the water-cooling techniques look wonderful!
This submit initially appeared on Customized PC, which has been protecting wonderful setups for over 20 years and is now a part of . Be a part of our 500k member Fb group to debate this construct.
For those who contemplate your self to be an knowledgeable PC builder, you possibly can submit your personal {custom} PC construct to us in the present day for an opportunity of being featured on sooner or later.
